How to replace an Axe Handle

Whistle Punks Urban Axe Throwing is the most satisfying day or night out you’ll ever have. You'll be slinging axes, hitting bullseyes and cheering on mates.

Always use a proper chopping block. Use the handle like a wedge and try to push it into the Avoid excessive force when pushing in the handle. Product details 3-way valve with female thread, PN 16 pn. So the new bought axe shaft should be left for a least a week in dry air, in a centrally-heated room for instance. In its history spanning more than years, the SAUTER Group has managed to position its name worldwide for expertise in the building management and room automation sector.

The SAUTER Group

The Viking axe was a very common weapon. Everyone owned a wood cutting axe that could be used as a dangerous weapon. Other axes were designed specifically for war. We stock all types of Viking axes included very historically accurate forged axes.

Product details 2-way valve with female thread, PN 16 pn. V6R 2-way valve with female thread, PN 16 pn. Product details 3-way valve with female thread, PN 16 pn. B6R 3-way valve with female thread, PN 16 pn. Product details 3-way flanged valve, PN 40 pn. BUS 3-way flanged valve, PN 40 pn. Product details 2-way flanged valve, PN 40 pn. To remove all or part of an old haft from a head is easy.

You just drill holes into the top until the rest can be driven out with a dull chisel or a drift. To put a new haft on an old axe head, the dimensions of the new shaft should be slightly bigger than the hole. This is important because old heads and new hafts seldom fit exactly. Mostly you see this in the width to length rations in the oval, round or triangular hafts.

To shape the haft to fit the eye, there are a number of methods. The easiest and most effective is to use a rasp. If you would like to use a drawknife or a spokeshave, even better!

Hold the end of the haft, well centered, against the bottom of the eye and from the other side use a sharp pencil to trace the contours of the hole onto the end of the haft. Then remove just enough wood so that you can push by hand the head onto the shaft. The pencil marks only help a little, mostly you have to work by eye, and trial and error. Before every use, make absolutely sure that the head is securely fixed to the haft.

A loose axe head is dangerous! If the axe will be stored for a while, oil the head to prevent rust. Inc VAT Shipping is extra. How to replace an Axe Handle. Axe hafts are usually machine made and so you can see that all the handles are made to the same dimensions to fit a certain kind of axe head. But with hand-forged axe heads the eye, or hole, formed by hand and eye, is always more or less different.

That means that the haft must usually be worked to achieve a proper fit. When the haft is inserted in the head, it should fill it out as much as possible, but an extremely fine fit is not necessary.

The haft and the wedge must be removed before the final installation. Together, they cited information from 15 references , which can be found at the bottom of the page. Acquire a handle suited to your axe. Axe handles are typically standardized, meaning that it should be easy for you to find a handle that fits your axe's blade. Axe handles may be purchased at a home hardware store. If you're networked with any woodworkers, they may be enticed into carving you a handle for a fee as well.

Purchasing a new axe outright is an option if you're going to the store to pick up a handle. Due to the fact that handles can be replaced fairly easily however, this is only recommended if you're strapped for time and need a new axe in a hurry. If you're truly a DIY type, you might consider making an axe handle from scratch.

Keep in mind, however, that this will require a lot of exact measurements and precise woodworking. Remove the old handle. Get out the old handle however you can. Here are a few ways you might go about it: Drill into the handle through the hole in the axe. Once you have a sufficient hole, insert a metal wedge and thrust it out by hitting the wedge with a hammer. Don't be afraid to bash it hard. After all, the old handle will be replaced as soon as it's out of there.

Saw off the handle, then hammer out the bit of handle that's still inside the blade. Clean the eye of the axe. Push out the excess pieces with a chisel, then smooth out the insides. Using sandpaper on the inside of the axe will ensure that all of the old handle has been properly removed.

The "eye" refers to the hole in the axe blade that the handle fits into. Mark the kerf of the new handle with a pencil. The "kerf" refers to the saw wedge in the top of the handle. This allows the handle to fit into the eye of the axe. Find the point on the handle where the kerf ends and trace a pencil line around the handle. This will offer a visual reference of how deep your handle needs to go.

Test fit the handle. The handle may need few tries to get in properly. Push it in and try to get it in manually at first. Next, tap it in lightly with a blunt piece of wood. Each time you push it in, check how far it gets in based on the bottom of the kerf. Although you shouldn't apply very much pressure when you're first starting out, this will hopefully give you a proper idea of the measurements the top of your handle needs to be.